Published record
Blade form-factor illustration, not a photograph of SVOLT CL03
Form-factor illustration · not a model photograph
LFP / LiFePO₄Blade

SVOLT CL03

SVOLT CL03: 196Ah, 3.2V LFP blade battery cell. weight 3.38kg.

Capacity

196Ah

Chemistry

LFP / LiFePO₄

Format

Blade

Weight

3.38kg

Specification

Engineering parameters

Core fields 3/4 · 0 individually confirmed fields
Coverage counts capacity, voltage, dimensions and weight; it does not certify the model. Missing fields are not zero. Expand each metric to inspect its conditions and evidence.

BrandSVOLT
ModelCL03
Form factorBlade
ChemistryLFP / LiFePO₄
Nominal capacity196Ah
Nominal voltage3.2V
ApplicationRechargeable
Energy (calculated)627 Wh
Gravimetric energy density (calculated)186 Wh/kg
Max continuous discharge
196 A
Conditions & source

discharge voltage is 2.0V.1.4.2 最大持续放电电流 Maximum Continuous discharge current 正常工作的单体电池25± 3 °C,196 A的恒流下进行放电。 At 25± 3°C, the maximum continuous discharge current is 196A.

Source version: V · Page 12

Source datasheet (access rules apply)
Max pulse discharge
1,000 A / 10 s
Conditions & source

正常工作的单体电芯25± 3 °C,50% SOC状态下,最大脉冲放电电流1000A,电芯温度低于50 °C,且最长放电时间为10 s。 The maximum cur rent of 10s pulse discharge is 1000A at 50%SOC at 25± 3°C, and the cell temperature shall not exceed 50 °C.1.4.5 绝对放电温度 Absolute charge temperature 持续放电模式或脉冲放电模式,若电芯温度超过绝对放电温度 -30~55 °C,则停止放电。 No matter what discharging mode (continuous or pulse discharge), the discharge will cut off immediately once the cell temperature exceeds -30°C-55°C.1.5 脉冲放电模式 Pulse discharge specification 是指在产品使用过程中,电芯进行脉冲放电。脉冲放电必须严格符合本产品标准所述的充电状态和电芯温度条件。脉冲电流的大小和持续时间必须严格遵守下表所列的所有充电状态以及电芯温度等条件。违反脉冲放电条件可能会造成电芯永久性的损坏并进而免除SVOLT 的产品质量责任。 During discharge, the current isn’t constant and changes in certain range with time . Pulse discharge must strictly comply with the charge state and temperature conditions of cells described in this specification. The value and continuous times of the pulse current must be also in strict accordance with the charge state and temperature conditions listed in table below. Violation of pulse discharge conditions may cause permanent damage to the cell and thereby exempt product quality responsibility of SVOLT.1.5.1 最小脉冲放电截止电压 Minimum pulse discharge limit voltage -30°C≤T≤55 °C

Source version: V · Page 13

Source datasheet (access rules apply)
Operating temperature
Charge -20–55 ℃; Discharge -30–55 ℃
Conditions & source

C, 65.3A (1/3C) DC to 2.0V 1.1.8 工作温度(充电) Operating temperature (Charge) -20 ~ 55°C 参考第 1.2、1.3 节 Refer to 1.2, 1.3 1.1.9 工作温度(放电) Operating temperature (discharge) -30 ~ 55°C 参考第 1.4、1.5 节 Refer to 1.4, 1.5

Source version: V · Page 7

Source datasheet (access rules apply)

2、1.3 节 Refer to 1.2, 1.3 1.1.9 工作温度(放电) Operating temperature (discharge) -30 ~ 55°C 参考第 1.4、1.5 节 Refer to 1.4, 1.5 1.1.10 循环寿命 Cycle life ≥2000 25°C, St ep charge/1C, 3-100%SOC , 80%SOH 1.1.11 室温放电功率 discha

Source version: V · Page 7

Source datasheet (access rules apply)
Internal resistance
≤0.45 mΩ · AC 1000 Hz
Conditions & source

ACR(1KHz) ≤0.45mΩ 25°C, 新电池 17%SOC 状态 25°C, BOL, 17%SOC

Source version: V · Page 7

Source datasheet (access rules apply)
Cell weight
3,380 g
Conditions & source

3% - 100% N.A.1.1.14 电池重量 Cell weight 3380±50 g N.A.1.1.15 日历寿命 Calendar life 1年 60°C 100% SOC

Source version: V · Page 8

Source datasheet (access rules apply)

Not provided: Voltage range, Dimensions, Max continuous charge, Max pulse charge, Cycle life.

Source note: Values should be verified against the latest manufacturer datasheet before pack design or procurement approval. Calculated values derive from the nominal figures above and are not manufacturer ratings.

Second source

Similar cells

Same chemistry and format, with nominal capacity within 10%. This is a starting point, not a confirmation that the cells are interchangeable.

Customer support

Datasheets, account access, and procurement enquiries.

Compose email